![]() ![]() Due to power consumption concerns, we recommend that the IS be turned off when shooting from a tripod, or at high enough shutter speeds that hand movement will not be a concern. However, using the IS feature on a lens will drain the battery much faster. Because the IS is optical, it will not deteriorate the quality of the image as digital image stabilization does. This can be useful for shooting fast-moving hand-held shots, shots in low-light environments, etc. ![]() Some canon lenses feature an optical IS (Image Stabilization) function. Regardless of the settings on the camera body, if the switch on the lens is set to MF (Manual Focus), the camera will not perform AF (Auto Focus) functions. The Canon Rebel uses an in-lens focusing system, which is switched on and off on the body of the lens. Line up the guide mark with the matching mark on the Canon rebel body, set the lens into the mount, and turn it approximately 90 degrees counter clockwise until it locks into place. ![]() If the lens is EF-S, the guide mark will be a white square. If it is an EF lens, the guide mark will be a red circle. To attach a new lens, find the guide mark on the lens body. To remove the lens, press this button, and turn the lens approximately 90 degrees clockwise. On the Canon Rebel, there is a half-circle shaped button on the right side of the lens mount (viewed from the front of the camera). Please do not remove the included kit lens from the camera unless you intend to attach a different lens immediately. Prime lenses (fixed focal length) are recommended for faster apertures and picture quality, while zoom lenses are recommended for changing shooting settings, or long telephoto applications. Media Loan has several different zoom and prime lenses that can be checked out alongside a Canon Rebel. The Canon Rebel will accept any Canon EF of EF-S bayonet lenses. If you know you will not be using the camera, it is best to fully turn the camera off. To wake the camera, press the shutter button down halfway. To conserve battery life, the Rebel will go into a sleep mode after a period of disuse. The Canon Rebel shows charge level in three stages: Battery OK, Battery Low, and Needs to be Charged. ![]() Because of this, make sure that the "Sensor Cleaning" logo is no longer on the screen before removing the battery. When the camera is powered off, it takes several seconds to clean the sensor. DO NOT USE ANY CHARGER OTHER THAN THE ONE PROVIDED WITH THE CAMERA. To charge the battery, slide it into the provided charger and then plug the charger into a standard 120 VAC outlet. The battery will only fit in one way, so if it does not seem to be working, the battery is not oriented correctly. The battery will slide into place and lock in. To insert a battery into the Canon rebel, open the battery door found on the bottom of the camera by pulling on the latch and swinging the door open. Please be gentle with this camera it looks hardy, but it's delicate! Store this camera in a location where there may be corrosive chemicals Use a blow dryer to blow dust from the camera Store this camera in excessive heat or cold Leave this camera in excessive heat, such as a car Leave this camera near a strong magnetic field! We appreciate your help in caring for this item to insure its long-term use at Evergreen. Media Loan has a limited number of Canon Rebel T1i/T2i cameras. 10 Aperture / Exposure Compensation Button.as long as you can power a refinery for 1/4 hour and build a extractor (basically an assembler) and a sensor you can build the rest using the materials produced. All powered by a couple of overpowered solar panels. So you could spawn 10k of stone evey minute, refine it in to gravel and convert that in to minerials to build what you want. They can be combined with a piston and timer block to trigger repeatedly for a steady source of materials. If you want to really cheat, you can use some of the mods on the work shop.ġ) Super powerful solar pannels, so you never run out of power for you base/capital ship again, especally if combined with over powered battery and a timer block.Ģ) uranium synasisers that take power and a small bit of uranium and make more uranium.Ĥ) Stone fuel mods, reactors that take gravel instead of uranium to run.ĥ) Minerial extaction mods that can either produce a range of minerials automatically or convert gravel to a specific minerial via an assembler type device menu, they run on either stone or gravel depending on the mod.Ħ) use despensor based sensors (example by Keen but has been updated by someone else) to spawn named items then triggered such as 1000 steel plates or 1k iron ore. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |